{"product_id":"pololu-i-c-isolator-with-isolated-power-and-connectors","title":"Pololu I²C Isolator with Isolated Power and Connectors","description":"\u003cp\u003eThis Pololu module enables galvanically isolated (electrically isolated), bidirectional communication between two I²C devices while providing isolated and regulated 5V or 3.3V power at up to 200mA.\u003c\/p\u003e\n\u003ctable width=\"474\"\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd width=\"107\"\u003e\u003cstrong\u003eInput voltage\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd width=\"225\"\u003e\u003cstrong\u003eOutput voltage\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd width=\"142\"\u003e\u003cstrong\u003eMax output current\u003c\/strong\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e4.5 V to 5.5 V\u003c\/td\u003e\n\u003ctd\u003e5 V (default) or 3.3 V (selectable)\u003c\/td\u003e\n\u003ctd\u003e200 mA\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e3 V to 3.6 V\u003c\/td\u003e\n\u003ctd\u003e3.3 V\u003c\/td\u003e\n\u003ctd\u003e75 mA\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003eThis isolation means that incorrect connections or bad voltages on one side cannot propagate through to damage the device connected to other side. The signal isolation is achieved with the TI ISO1640B, which supports bidirectional data transfer up to 1.7 MHz. See the\u003cspan\u003e \u003c\/span\u003eISO1640BDR datasheet\u003cspan\u003e \u003c\/span\u003efor more information.\u003c\/p\u003e\n\u003cp\u003eThe isolated power transfer is achieved with the MPS MIE1W0505BGLVH. The output ground (GND2) is effectively independent of the input side, which can be useful for preventing ground loops and avoiding ground currents that can cause unpredictable system behavior or even lead to destruction. See the\u003cspan\u003e \u003c\/span\u003eMIE1W0505BGLVH datasheet for more information.\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003eThis is the version with JST-SH (Qwiic\/STEMMA QT compatible) connectors, allowing easy connections with \u003c\/span\u003eJST-SH 4-pin cables\u003cspan\u003e. We also stock a \u003c\/span\u003eversion with no connectors, which may be better for compact projects with directly soldered wires\u003cspan\u003e.\u003c\/span\u003e\u003c\/p\u003e\n\u003ch2\u003eFeatures\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eGalvanic isolation between the two sides\u003c\/li\u003e\n\u003cli\u003eBidirectional SDA and SCL for bidirectional I²C communication with support for clock stretching\u003c\/li\u003e\n\u003cli\u003e3 V to 5.5 V input voltage range\u003c\/li\u003e\n\u003cli\u003eSelectable 5 V or 3.3 V regulated output (5 V default)\n\u003cul\u003e\n\u003cli\u003eUp to 180 mA out continuous (200 mA peak) at 5 V in\u003c\/li\u003e\n\u003cli\u003eUp to 75 mA out continuous at 3 V in\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/li\u003e\n\u003cli\u003eOver-temperature and short-circuit protection\u003c\/li\u003e\n\u003cli\u003eCompact 0.5″ × 0.6″ size with breadboard-compatible, 0.1″-pitch through holes\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eUsing the module\u003c\/h2\u003e\n\u003cp\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0176\/3274\/files\/Pololu_I_C_Isolator_with_Isolated_Power_and_Connectors_pinout.jpg?v=1742944119\u0026amp;width=700\" alt=\"\"\u003e\u003c\/p\u003e\n\u003cp\u003eInput power is supplied across\u003cspan\u003e \u003c\/span\u003e\u003cstrong\u003eVCCIN\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003eand\u003cspan\u003e \u003c\/span\u003e\u003cstrong\u003eGND1\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003eand output power is delivered across\u003cspan\u003e \u003c\/span\u003e\u003cstrong\u003eVCCOUT\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003eand\u003cspan\u003e \u003c\/span\u003e\u003cstrong\u003eGND2\u003c\/strong\u003e. The two sides are galvanically isolated (GND1 is\u003cspan\u003e \u003c\/span\u003e\u003cem\u003eNOT\u003c\/em\u003e\u003cspan\u003e \u003c\/span\u003econnected to GND2). Note that the efficiency of the regulator is less than 50%, so the input power will need to be at least twice the output power.\u003c\/p\u003e\n\u003ctable width=\"494\"\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd width=\"103\"\u003e\u003cstrong\u003eVCCIN range\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd width=\"91\"\u003e\u003cstrong\u003eVSEL\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd width=\"75\"\u003e\u003cstrong\u003eVCCOUT\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd width=\"225\"\u003e\u003cstrong\u003eOutput current\u003c\/strong\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd rowspan=\"2\"\u003e4.5 V to 5.5 V\u003c\/td\u003e\n\u003ctd\u003eNC (default)\u003c\/td\u003e\n\u003ctd\u003e5 V\u003c\/td\u003e\n\u003ctd rowspan=\"2\"\u003e180 mA continuous, 200 mA peak\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eGND2\u003c\/td\u003e\n\u003ctd\u003e3.3 V\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e3 V to 3.6 V\u003c\/td\u003e\n\u003ctd\u003eGND2\u003c\/td\u003e\n\u003ctd\u003e3.3 V\u003c\/td\u003e\n\u003ctd\u003e75 mA continuous\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e\u003cstrong\u003eSDA1\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003eand\u003cspan\u003e \u003c\/span\u003e\u003cstrong\u003eSCL1\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003econnect to the I²C data and clock signals of one device while\u003cspan\u003e \u003c\/span\u003e\u003cstrong\u003eSDA2\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003eand\u003cspan\u003e \u003c\/span\u003e\u003cstrong\u003eSCL2\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003econnect to the I²C data and clock signals of the other. Both the SDA and SCL connections are bidirectional, which allows for clock stretching. There are 10k pull-up resistors from SDA1 and SCL1 to VCC1 and from SDA2 and SCL2 to VCC2; for high-speed communication, external pull-up resistors can be added in parallel as necessary to make the pull-ups stronger.\u003c\/p\u003e\n\u003cp\u003eThe enable input,\u003cspan\u003e \u003c\/span\u003e\u003cstrong\u003eEN\u003c\/strong\u003e, is pulled up to VCCIN through a 100 kΩ resistor, which enables the power transfer to the VCCOUT side by default. This pin can be driven low to disable the module and put it into a low-power state (note that the input side of the ISO1640 is not powered down).\u003c\/p\u003e\n\u003cp\u003eThe output voltage selection pin,\u003cspan\u003e \u003c\/span\u003e\u003cstrong\u003eVSEL\u003c\/strong\u003e, is floating, which sets the output voltage to 5 V by default. To select 3.3 V for the output voltage, connect VSEL to GND2. This can be done using the board’s through holes (the left picture below shows an example of this with\u003cspan\u003e \u003c\/span\u003emale headers\u003cspan\u003e \u003c\/span\u003eand a\u003cspan\u003e \u003c\/span\u003eshorting block) or by adding an SMT jumper to the pads circled in the image below.\u003cspan\u003e \u003c\/span\u003e\u003cins\u003e\u003cstrong\u003eNote:\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003eDo not change VSEL while the regulator is powered.\u003c\/ins\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0176\/3274\/files\/Pololu_I_C_Isolator_with_Isolated_Power_SMT_jumper.jpg?v=1742943722\u0026amp;width=700\" alt=\"\"\u003e\u003c\/p\u003e\n\u003ch3\u003eIsolation\/clearance considerations\u003c\/h3\u003e\n\u003cp\u003eAlthough the ISO1640 IC has an isolation rating of up to 3 kVRMS and the MIE1W0505BGLVH IC has an isolation rating up to 2.5 kVRMS, please note that the board is made to be compact, and the tightest clearance (2 mm) is smaller than clearances of the IC packages (4mm for the ISO1640 and 3.5 mm for the MIE1W0505BGLVH). The picture below shows the regions of tightest clearance (the larger pads are just structural pads for the connectors and are not electrically connected to anything):\u003c\/p\u003e\n\u003cp\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0176\/3274\/files\/Pololu_I_C_Isolator_with_Isolated_Power_clearance.jpg?v=1742943735\u0026amp;width=700\" alt=\"\"\u003e\u003c\/p\u003e\n\u003ch2\u003eSpecifications\u003c\/h2\u003e\n\u003ctable width=\"411\"\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd width=\"257\"\u003e\u003cstrong\u003eMinimum operating voltage\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd width=\"154\"\u003e3.0 V\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eMaximum operating voltage\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e5.5 V\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eMaximum output current\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e200 mA\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eOutput voltage\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e5 V\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eReverse voltage protection?\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eN\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eConnectors?\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eY\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eIsolated power transfer?\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eY\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eSize\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e0.5″ × 0.6″ × 0.28″\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eWeight\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e0.7 g\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003ch2\u003eResources\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eSchematic\u003c\/li\u003e\n\u003cli\u003eDimensions\u003c\/li\u003e\n\u003cli\u003e3D Model (STEP)\u003c\/li\u003e\n\u003cli\u003eDrill guide\u003c\/li\u003e\n\u003cli\u003eMPS MIE1W0505BGLVH datasheet\u003c\/li\u003e\n\u003cli\u003eTI ISO1640BDR datasheet\u003c\/li\u003e\n\u003cli\u003eMIE1W0505BGLVH MPS product page\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Pololu","offers":[{"title":"Default Title","offer_id":43643945091133,"sku":"kts1789699595331","price":8.54,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0658\/9716\/8957\/files\/pololu-i_c-isolator-with-isolated-power-and-connectors_1.jpg?v=1789699599","url":"https:\/\/laser-engraved-clasp.shop\/products\/pololu-i-c-isolator-with-isolated-power-and-connectors","provider":"My Store","version":"1.0","type":"link"}