{"product_id":"pololu-isolated-dc-dc-power-module-5v33v-200ma","title":"Pololu Isolated DC-DC Power Module (5V\/3.3V 200mA)","description":"\u003cp\u003eThis Pololu DC-DC power module provides galvanically isolated (electrically isolated) and regulated 5V or 3.3V power at up to 200 mA, as follows:\u003c\/p\u003e\n\u003ctable width=\"487\"\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd width=\"108\"\u003e\u003cstrong\u003eInput voltage\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd width=\"236\"\u003e\u003cstrong\u003eOutput voltage\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd width=\"143\"\u003e\u003cstrong\u003eMax output current\u003c\/strong\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e4.5 V to 5.5 V\u003c\/td\u003e\n\u003ctd\u003e5 V (default) or 3.3 V (selectable)\u003c\/td\u003e\n\u003ctd\u003e200 mA\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e3 V to 3.6 V\u003c\/td\u003e\n\u003ctd\u003e3.3 V\u003c\/td\u003e\n\u003ctd\u003e75 mA\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003eUnlike non-isolated regulators, the output ground (GND2) is effectively independent of the input side, which can be useful for preventing ground loops and avoiding ground currents that can cause unpredictable system behavior or even lead to destruction.\u003c\/p\u003e\n\u003cp\u003eThis module is based on the MPS MIE1W0505BGLVH, which has a 2.5 kVRMS isolation rating; the PCB is designed with the same 3.5 mm minimum clearance and creepage between the isolated sides as the IC, but please note that the module itself is not certified to any standard. See the MIE1W0505BGLVH datasheet for more information.\u003c\/p\u003e\n\u003ch2\u003eFeatures\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eGalvanic isolation between input and output\u003c\/li\u003e\n\u003cli\u003e3 V to 5.5 V input voltage range\u003c\/li\u003e\n\u003cli\u003eSelectable 5 V or 3.3 V regulated output (5 V default)\n\u003cul\u003e\n\u003cli\u003eUp to 180 mA out continuous (200 mA peak) at 5 V in\u003c\/li\u003e\n\u003cli\u003eUp to 75 mA out continuous at 3 V in\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/li\u003e\n\u003cli\u003eOver-temperature and short-circuit protection\u003c\/li\u003e\n\u003cli\u003eCompact 0.3″ × 0.6″ size with breadboard-compatible, 0.1″-pitch through holes\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eUsing the module\u003c\/h2\u003e\n\u003cp\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0176\/3274\/files\/Isolated_DC-DC_Power_Module_pinout.jpg?v=1742932529\u0026amp;width=700\" alt=\"\"\u003e\u003c\/p\u003e\n\u003cp\u003eInput power is supplied across\u003cspan\u003e \u003c\/span\u003e\u003cstrong\u003eVIN\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003eand\u003cspan\u003e \u003c\/span\u003e\u003cstrong\u003eGND1\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003eand output power is delivered across\u003cspan\u003e \u003c\/span\u003e\u003cstrong\u003eVOUT\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003eand\u003cspan\u003e \u003c\/span\u003e\u003cstrong\u003eGND2\u003c\/strong\u003e. The two sides are galvanically isolated (GND1 is\u003cspan\u003e \u003c\/span\u003e\u003cem\u003eNOT\u003c\/em\u003e\u003cspan\u003e \u003c\/span\u003econnected to GND2). Note that the efficiency of this regulator is less than 50%, so the input power will need to be at least twice the output power.\u003c\/p\u003e\n\u003ctable width=\"518\"\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd width=\"119\"\u003e\u003cstrong\u003eVIN range\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd width=\"96\"\u003e\u003cstrong\u003eVSEL\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd width=\"79\"\u003e\u003cstrong\u003eVOUT\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd width=\"224\"\u003e\u003cstrong\u003eOutput current\u003c\/strong\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd rowspan=\"2\"\u003e4.5 V to 5.5 V\u003c\/td\u003e\n\u003ctd\u003eNC (default)\u003c\/td\u003e\n\u003ctd\u003e5 V\u003c\/td\u003e\n\u003ctd rowspan=\"2\"\u003e180 mA continuous, 200 mA peak\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eGND2\u003c\/td\u003e\n\u003ctd\u003e3.3 V\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e3 V to 3.6 V\u003c\/td\u003e\n\u003ctd\u003eGND2\u003c\/td\u003e\n\u003ctd\u003e3.3 V\u003c\/td\u003e\n\u003ctd\u003e75 mA continuous\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003eThe enable input,\u003cspan\u003e \u003c\/span\u003e\u003cstrong\u003eEN\u003c\/strong\u003e, is pulled up to VIN through a 100 kΩ resistor, which enables the regulator by default. This pin can be driven low to put the device into a low-power state where the shutdown current draw is typically dominated by the current through the pull-up resistor (10 µA per volt on VIN).\u003c\/p\u003e\n\u003cp\u003eThe output voltage selection pin,\u003cspan\u003e \u003c\/span\u003e\u003cstrong\u003eVSEL\u003c\/strong\u003e, is floating, which sets the output voltage to 5 V by default. To select 3.3 V for the output voltage, connect VSEL to GND2. This can be done using the board’s through-holes or by adding an SMT jumper to the pads circled in the picture below.\u003cspan\u003e \u003c\/span\u003e\u003cins\u003e\u003cstrong\u003eNote:\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003eDo not change VSEL while the regulator is powered.\u003c\/ins\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0176\/3274\/files\/Isolated_DC-DC_Power_Module_smt_jumper.jpg?v=1742932528\u0026amp;width=700\" alt=\"\"\u003e\u003c\/p\u003e\n\u003ch2\u003eSpecifications\u003c\/h2\u003e\n\u003ctable width=\"437\"\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd width=\"295\"\u003e\u003cstrong\u003eMinimum operating voltage\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd width=\"142\"\u003e3.0 V\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eMaximum operating voltage\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e5.5 V\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eMaximum output current\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e200 mA\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eOutput voltage\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e5 V\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eReverse voltage protection?\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eN\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eMaximum quiescent current\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e8 mA\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eSize\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e0.3″ × 0.6″ × 0.1″\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eWeight\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e0.5 g\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003ch2\u003eResources\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eDimensions\u003c\/li\u003e\n\u003cli\u003e3D Model (STEP)\u003c\/li\u003e\n\u003cli\u003eDrill guide\u003c\/li\u003e\n\u003cli\u003eSchematic\u003c\/li\u003e\n\u003cli\u003eMIE1W0505BGLVH MPS Product Page\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Pololu","offers":[{"title":"Default Title","offer_id":43643946139709,"sku":"jvk1789699605777","price":5.4,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0658\/9716\/8957\/files\/pololu-isolated-dc-dc-power-module-5v33v-200ma_1.jpg?v=1789699633","url":"https:\/\/laser-engraved-clasp.shop\/products\/pololu-isolated-dc-dc-power-module-5v33v-200ma","provider":"My Store","version":"1.0","type":"link"}